Your Plumbing Crash Course: Tips for Installing a Bathtub
Your Plumbing Crash Course: Tips for Installing a Bathtub
Blog Article
They are making several good annotation related to How to Install a Bathtub Yourself overall in this post underneath.
Setting up a tub isn't specifically rocket science, but it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately hard project. If the old bathtub is easily obtainable, the project can move immediately; if you have to open a wall surface to get rid of the old bathtub as well as position the brand-new tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to leave the old tub and embeded in the new one. Ensure you have actually certified yourself for the task and also fit trying it. Rather than working with a specialist to take control of a halfway-completed task, it is far better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly help you mount a new bathtub in your bathroom if you have actually already acquired a brand-new bathtub as well as don't require to transform the setup of your previous water system pipelines.
Your tools and material list need to consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite bothersome because of the limited gain access to that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this process. When the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers are in area between the tap and also the sink. Safeguard the tap in position with the maker given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type should be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the called for position. The wooden boards are useful in equally spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile tap port to the ideal supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also inspect all joints and brand-new pipework for leakages and tighten them if necessary. Load the tub as well as likewise check the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will certainly resolve it into its final position.
Getting ready for the Installment
Firstly, the supporting frame supplied with the bath needs to be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final position.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack an inflexible seal, creating the water to permeate the wall in between the bath and also the tiling, leading to difficulties with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack fairly early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the floor tiles using waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading up on How to Install a Bathtub? Place a remark below. We'd be interested to know your opinion about this blog post. Hoping that you visit us again in the future. If you please take the time to distribute this blog posting if you enjoyed it. We enjoy reading our article about Tools You Need to Install a New Bathtub .
Trusted by locals for emergencies. Report this page